minimum thickness造句
例句與造句
- The minimum thickness of the workpieces
零件的最小壁厚 - If you ship your fabric or wallpaper roll in a bag , please use a bag with a minimum thickness of 6 mm
如果您用袋子運輸紡織品或墻紙卷，請使用厚度至少為六密耳的袋子 - If you ship your fabric or wallpaper roll in a bag , please use a bag with a minimum thickness of 6 mm
如果您使用膠袋來托運織物或墻紙，請使用厚度至少有六密爾單位的膠袋 - Am218 . 1 ( d ) , 原文 為 ： the governing thickness of a nonwelded dished head is the greater of the flat flange thickness divided by 4 or the minimum thickness of the dished portion
2004及以前版譯為：非焊接碟形封頭的控制厚度為較大的平法蘭厚度除以4或碟形封頭部分的最小厚度。 - The chinese codes stipulate both the width - thickness ratio and the minimum thickness of the elements . that is stricter than the stipulations of north american codes
對于受壓板件的壁厚，我國規范采取的是既限制板件寬厚比又限制最小板厚的規定，其限制較北美同類規范偏嚴。 - It's difficult to find minimum thickness in a sentence. 用minimum thickness造句挺難的
- Aerospace series . lubricating dry fluorocarbonated coating with binding material and fillers , of a minimum thickness of 5 micrometers on metallic substrate . quality of coated parts
航空航天系列.金屬底層最小厚度5微米的帶粘接材料和填料的干潤滑碳氟化合物覆層.覆層零件質量 - The axial frictional pulling force and the minimum thickness of mucus film were analyzed and calculated in detail when rectangular or trapezoidal cylindrical screw was being adopted in microcomputer
詳細分析計算了微型機器人在采用矩形和梯形圓柱螺旋時的軸向摩擦牽引力和最小粘液膜厚度。 - V - class thermistor film is successfully produced on silicon substrate and sio2 substrate applying cvd process for the first time in this paper , whose minimum thickness is only 600nm or so
本論文創沃性地采用十導體cvd工藝在硅中晶1底以及引；襯底1二if長出最小厚度為600urn的v系熱敏電阻薄臟。 - Nominal thickness of insulatioh should be in accordance with the stipulations of table 1 , table2 . - 10 % discrepancy is allowed , but the minimum thickness should be not less than 90 % - 0 . 1 of nominal thickness
2絕緣絕緣標和厚度符合表1 、表2的規定，允許有- 10 %的偏差，其最薄厚度應不小于標稱厚度的90 % - 0 . 1 - Wherethe long bridge deck within 0 . 5 l amidships is regarded as strengthdeck , the midship section modulus and minimum thickness of the deckplating comply with the requirements of 2 . 2 . 1 and 2 . 4 . 2 . l of this ischapter
例1 :在船中部0 . 5l區域內的長橋樓甲板作為強力甲板時，其船中剖面模數及最小厚度應滿足本章2 . 2 . 1及2 . 4 . 2 . 1的要求。 - The minimum thickness of sheath and maximum overall diameter of cables for analogue conversion lan are to see table 2 , and the minimu thickness of sheath and maximum overall diameter of cable for digital conversion lan are to table 3
模擬交換用局用電纜的護套最小厚度和電纜最大外徑見表2 ；數字交換用局用電纜的護套最小厚度和電纜最大外徑見表3 。 - The production ability of thin steel sheet in china is promoted . however , limited by the ability of production and anti - corrosion , the limitation of the minimum thickness could not fulfill the requirements of the development
隨著生產的發展，我國薄鋼板的生產能力已大大提高，限于生產能力和防腐能力而對最小壁厚作出的構造限制已不符合當前生產和技術發展的需要。 - Chapter two constructed the mathematical model of robot and its environment solved by the fem analysis . the functions or relations between the robotic parameters and its drive forces , thickness or its velocities were given , and also the functions or relations between the environment and the robot force , friction , robot velocity , minimum thickness of film or sustain force of dynamic films were given
論文第二章通過建立機器人和環境的數學模型，利用有限元方法求解其中的n - s方程，得出管道中微型機器人的各種設計參數與機器人的驅動力、形成的最小潤滑油膜厚度和機器人的運行速度之間的關系曲線，研究了管道環境與機器人驅動力、摩擦阻力矩、機器人運行速度、形成的最小潤滑油膜厚度、油膜的承載能力之間的關系。